Restting DAS on Maytag Washers and Dryers

 

Have you ever seen "DAS" or "das" show up on your display board on your Maytag washers or dryers?
Here is how you get rid of that thanks to the WASH Commercial Laundry technician staff:

Ev

RESETTING DAS MODE ON MAYTAG CONTROL BOARDS

MHN33, MAT20, MLx22, MDx20, MDx28 

1. Power machine OFF, then back ON: “Sync” appears, then disappears
2. Press buttons in this sequence:
• MHN33 – Delicates / PowerWash / Delicates / Normal / PowerWash + Delicates
• MAT20 – Delicates / PowerWash / Delicates / Mixed / PowerWash + Delicates
• MLx22 – Delicates / PowerWash / Delicates / Normal / PowerWash + Delicates
• MDx20/28 – Delicates / Whites&Colors / Delicates / Perm Press / Delicates + Whites&Colors
3. “HHHHHHHH” will appear
4. Press buttons in this sequence:
• MHN33 – Delicates / Delicates / Delicates / PowerWash + Delicates
• MAT20 – PowerWash / PowerWash / PowerWash / PowerWash + Delicates
• MLx22 – Delicates / Delicates / Delicates / PowerWash + Delicates
• MDx20/28 – Delicates / Delicates / Delicates / Delicates / Delicates + Whites&Colors
5. “RES” will appear if successful
6. Power OFF, then power ON
7. Unit has been reset to factory default settings

MHN30, MAH22, MVW18 (using buttons on left)
1. Power machine OFF, then back ON: “Sync” appears, then disappears
2. Press bottom row buttons in this sequence: right/left/right/middle/left + right
3. “HHHHHHHH” will appear
4. Press bottom row buttons in this sequence: left/left/left/left + right
5. “RES” will appear if successful
6. Power OFF, then power ON
7. Unit has been reset to factory default settings

Method #1 for other models:
1. Open service switch (OMIT for MFRxxPDATS)
2. Disconnect power from machine (unplug)
3. Restore power
4. Hold DELICATES button until board flashes
5. Open door/lid
6. Close service switch
 ***The next sequence must be done within 6 seconds***
Washers and stack dryers - use the lower-case buttons, single dryers only have 3 buttons
7. Press buttons in this order: left/middle/left/middle/left/right
8. Remove power from machine (unplug)
9. Restore power and release service switch;
if done correctly the “dAS” will be gone and the board will ready to program as normal

MLG dryers
1. Put unit into programming mode
2. Go to Factory Settings
3. Enter password using buttons in this sequence: left/middle/left/middle/right/middle/left
4. Program board as needed; make sure to select correct configuration (example: gas, non-reversing)

Method #2 for other models:
1. Open service switch
2. Remove wire from coin vault switch
3. Close lid/door
4. Remove the coin drop (do not disconnect from the board)
5. Remove power from machine for 6 seconds
6. Restore power
7. Hold the DELICATES button until board flashes
8. Block coin optic for 1 second or more
9. Unblock the coin optic
10.Open lid/door
11.Closed service switch
***The next sequence must be done within 6 seconds***
Washers and stack dryers - use the lower-case buttons, single dryers only have 3 buttons
12.Press buttons in this order: Left/middle/left/middle/left/right
13.Remove power from the machine
14.Restore power;
if done correctly the “dAS” will be gone and the board will be ready to program as normal